Ua Koj Tus Kheej Koj Tus Kheej Cov Khoom Siv Txiaj Ntsig nrog Lub Rooj Tsis Muaj - LackRack

首图.png   

Lately, I required a 19 ″ devices rack. But being cheap, I made a decision to develop one. While searching the Internet, I found what is called a backpack, which utilizes IKEA's Lack Table. However further reading exposed a number of things that I assumed were not have in the initial design of the backpack.

   

Upon doing more study on using a Lack Table for a 19 ″ tools shelf, I found out that the legs of the Absence Table were hollow, besides the top 2 inches, and also the bottom inch. It would probably be okay if you just needed to rack one piece of gear, yet that sort of seems to defeat the function of having a 19-inch rack.

   

What I determined to do on my 19 ″ devices rack was to make use of steel enhancing strips as rack rails. However initially, right here is a picture of the completed 19-inch devices shelf making use of an IKEA Lack table:

   

1.jpg

  

I picked to place my equipment on the inside of the legs for a neater appearance because I was placing metal rails on the legs of the Absence table. This additionally offers me a more comfy sensation when I placed my coffee cup in addition to the Lack table, as coffee spills are inevitable, placing the tools as shown will certainly supply more defense from such accidents

  

The first thing to do is to construct the Lack Table. Once that is done, then it's time to make it a 19-inch device's shelf. Begin by reducing 2 items of 1 ″ vast 1/8 ″ thick lightweight aluminum 15 inches long. After that take your Absence Table and flip it upside-down, as well as place one of the items of aluminum up against them on one of the legs of the Absence Table. after that take an item of your equipment you wish to rack and also press it against the inside legs of the Absence Table like the picture below:

   

2.jpg   

  

Next off, make certain the item of lightweight aluminum isn't revealing from the front, and also note the leading opening of your devices (the one closest to the tabletop) onto the aluminum. Do this for both legs, as this will establish the proper size for your 19 ″ devices rack. This mark must be 1/4 ″ from the side of the lightweight aluminum strip.

19-inch tools racks have very specific dimensions, which can be found here.

  

I made a design template out of a scrap piece of wood based on the dimensions labeled "2U" in the drawing, but as opposed to piercing a hole for a 10-32 screw in the wood, I drilled 1/8 ″ openings. This scrap piece of wood can currently be used to transfer the correct measurements of the screw openings on the 1 ″ lightweight aluminum. Beginning by aligning the initial opening with your first mark. After that take a tiny nail as well as the faucet in each hole. This will note the correct dimensions of the screw holes for your equipment shelf.

   

Once they are significant, pierce out the marked spots on the aluminum using a 1/8 ″ drill bit. As you most likely observed, 19 ″ tools shelves make use of 10-32 touched holes for mounting. What I used rather were # 10 self-tapping screws. By doing this, I really did not have to touch the holes in the aluminum. After both items of lightweight aluminum are drilled, the next thing to do is to pierce a 3/16 ″ hole at the top and base of the lightweight aluminum. These holes will certainly be used to protect the lightweight aluminum rails to the Absence Table. The top and also the base of the legs are not hollow. These two screws are key to maintaining your devices safe to the Absence Table.

  

3.jpg

   

The picture to the right shows one piece of lightweight aluminum drilled out with two pieces of equipment installed.

   

Likewise see the additional screw that is close to the underside of the table, however only screwed right into the aluminum. This is the screw that screws right into the strong part of the table leg. You will additionally require one similar to this at the end of the table leg.

  

Here is one more image of the finished LackRack:

   

4.jpg

   

Although the backpack is an economical solution for a 19-inch equipment rack, it is not intended for strong use and is also most definitely not meant for any kind of type of traveling tools rack.

   

As an added choice, you could want to include some kind of bracket from the rear of your devices to the underside of the tabletop. Another wonderful feature to add is a tiny light so you can easily see your equipment. While you are at IKEA, you can likewise grab one of their several great lights for this.

   

This write-up was originally published on mikestechblog.com. Any type of reproduction on any other website is forbidden and also a violation of copyright regulations.

Tags

Muab cov ntawv no

Tau txais cov ntsiab lus lag luam zoo tshaj plaws rau lub lim tiam

txheem

    lwm yam khoom

    NCO NTSOOV

    TIV TAUJ PEB

    contact-email
    tiv-logo

    FMUSER INTERNATIONAL GROUP LIMITED.

    Peb ib txwm muab peb cov neeg siv khoom nrog cov khoom lag luam txhim khu kev qha thiab kev pabcuam siab.

    Yog tias koj xav tiv tauj peb ncaj qha, thov mus rau hu rau peb

    • Home

      Tsev

    • Tel

      Tel

    • Email

      Email

    • Contact

      Tiv tauj